logo
Welcome, Guest. Please Login or Register.
28. March 2024, 18:37:40


Home Help Search Login RegisterWIKIUHSDR Download

Amateurfunk Sulingen
Diskussions- und Newsboard des DARC-Ortsverbandes I40  |  allgemeine Kategorie  |  UHSDR Firmware (Moderators: DF8OE, DL1PQ)  |  Topic: I2C speed in F7 <- zurück vorwärts ->
Pages: [1] Go Down Print
   Author  Topic: I2C speed in F7  (Read 1328 times)
Co
schon länger dabei
**

Offline

Posts: 79



Ich liebe dieses Forum!

View Profile
I2C speed in F7
« on: 19. August 2020, 09:43:12 »

Hello,

Is the i2c speed in the  F7 still adjustable via a menu option ?

Regards

Co
Logged
DF8OE
Administrator
*****

Offline

Posts: 6268



Stellvertr. OVV I40, Jugend / Nachwuchsreferent

View Profile WWW
Re:I2C speed in F7
« Reply #1 on: 19. August 2020, 10:05:39 »

Hi Co,

no, its fixed.

vy 73
Andreas
Logged

Wenn der Wind des Wandels weht, nageln die einen Fenster und Türen zu und verbarrikadieren sich. Die anderen gehen nach draußen und bauen Windmühlen...
qrz.com-Seite von DF8OE
-----------------------------------------------------
>>>> Die Inhalte meiner Beiträge dürfen ohne meine explizite Erlaubnis in jedwedem Medium weiterverbreitet werden! <<<<
Co
schon länger dabei
**

Offline

Posts: 79



Ich liebe dieses Forum!

View Profile
Re:I2C speed in F7
« Reply #2 on: 19. August 2020, 14:24:46 »

Hello Andreas,

I'm trying to bring a OVI40 V1.7 board back to live again. Its runs stand alone 5V on pin 28. It boots but get 
the WM8731 error message at boot up. The I2C connections seem to be OK.  I do however measure 2.5 volts on pin 27
P1 (UI-3V soft)is floating (RF board is not connected). So worst case : I've blown up the codecs one way or the other.    .  Could you think of something else.

Regards

Co
Logged
DF8OE
Administrator
*****

Offline

Posts: 6268



Stellvertr. OVV I40, Jugend / Nachwuchsreferent

View Profile WWW
Re:I2C speed in F7
« Reply #3 on: 19. August 2020, 14:58:34 »

Hi Co,

first you need to test if analog & digital 3.3V supply for the codecs is present (on BOTH codecs).
Second you have to test if SDA and SCL from both codecs are connected to the correspondent MCU pin and nothing else
Third you an chekc for bad solderings at codecs.

For testing you can connect a scope to SDA and SCL and check if there is "life" when powering up UI PCB for a small time. Amplitude must reach 0V/3.3V.

Good luck - feedback if you have fixed it is welcome  !

vy 73 - stay healthy
Andreas
Logged

Wenn der Wind des Wandels weht, nageln die einen Fenster und Türen zu und verbarrikadieren sich. Die anderen gehen nach draußen und bauen Windmühlen...
qrz.com-Seite von DF8OE
-----------------------------------------------------
>>>> Die Inhalte meiner Beiträge dürfen ohne meine explizite Erlaubnis in jedwedem Medium weiterverbreitet werden! <<<<
Pages: [1] Go Up Print 
Diskussions- und Newsboard des DARC-Ortsverbandes I40  |  allgemeine Kategorie  |  UHSDR Firmware (Moderators: DF8OE, DL1PQ)  |  Topic: I2C speed in F7 <- zurück vorwärts ->
Jump to: 


Login with username, password and session length

 Es wird die Verwendung von Browsern die auf der "Blink"-Engine basieren und mindestens
1024x768 Pixel Bildschirmauflösung für die beste Darstellung empfohlen
 
Amateurfunk Die Beiträge sind, sofern nicht anders vermerkt, unter der folgenden Lizenz veröffentlicht:
GNU Free Documentation License 1.3 GNU Free Documentation License 1.3
verbindet!
Powered by MySQL Powered by PHP Diskussions- und Newsboard des DARC-Ortsverbandes I40 | Powered by YaBB SE
© 2001-2004, YaBB SE Dev Team. All Rights Reserved.
- modified by Andreas Richter (DF8OE)
Impressum & Disclaimer
Valid XHTML 1.0! Valid CSS!