Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung | ||
ovi40test:uiboardtest [18.01.2018 23:59] – df9ts | ovi40test:uiboardtest [21.03.2018 07:39] (aktuell) – dg8ygw | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
- | {{tag>stub}} | + | {{tag>review}}{{tag> |
===== UI Board Test & Fehlersuche ===== | ===== UI Board Test & Fehlersuche ===== | ||
- | die MCU hat zwei (!) Pin 1 Markierungen | ||
- | < | ||
- | [{{: | ||
- | [{{: | + | ==== EEPROM IC7 Einbau Lage ==== |
+ | |||
+ | [{{: | ||
+ | |||
+ | This is where the dot is printed. Also the edge of the case is slanted near the 1-4 pins. See [[http:// | ||
+ | |||
+ | ==== Achtung: MCU Pin1 Markierung ==== | ||
+ | |||
+ | die MCU hat zwei (!) Pin 1 Markierungen < | ||
+ | |||
+ | [{{: | ||
< | < | ||
Zeile 15: | Zeile 22: | ||
Flashprobleme: | Flashprobleme: | ||
+ | |||
* Uhrenquarz und TCXO sind für das Flashen beide absolute Voraussetzung. | * Uhrenquarz und TCXO sind für das Flashen beide absolute Voraussetzung. | ||
* Bitte genau prüfen ob der TCXO richtig herum eingelötet ist! | * Bitte genau prüfen ob der TCXO richtig herum eingelötet ist! | ||
* wenn die 3V3 am C95 nicht mehr anliegen ist L3 wohl defekt | * wenn die 3V3 am C95 nicht mehr anliegen ist L3 wohl defekt | ||
- | Helle LEDS: Mit den Bausatz-Vorwiderständen leuchten die LEDs sehr hell. DF9EH hat die Werte reduziert: | + | Helle LEDS: Mit den Bausatz-Vorwiderständen leuchten die LEDs sehr hell. DF9EH hat die Werte reduziert: |
* R36 auf 22,6k (D1 grün) | * R36 auf 22,6k (D1 grün) | ||
* R37 auf 6,8k (D2 rot) | * R37 auf 6,8k (D2 rot) | ||
* R116 auf 6,8k (D3 blau) | * R116 auf 6,8k (D3 blau) | ||
- | ==== MCU wiederbeleben ("bricked MCU") ==== | + | ==== "WM8731 not detected" |
- | If something strange or unexpected happened to your board and none of the usual procedure are working to install the Bootloader or the Firmware, this might bring life back into your UI. | + | |
+ | Bei UHSDR Fehlermeldung " | ||
+ | |||
+ | ==== MCU läuft gar nicht, auch DFU Verbindung geht nicht ==== | ||
+ | |||
+ | Zuerst prüfen, ob die MCU in korrekter Lage eingelötet wurde ("Pin 1"). | ||
+ | |||
+ | Nach dem booten legt die MCU 3.3V an die Taster. Um erfolgreich zu booten braucht die MCU: | ||
+ | |||
+ | * CPU Takt (→ TCXO Takt messen) | ||
+ | * Korrekten Spannungsreset (→ Spannungsverlauf und Spannungspegel am Reset Pin messen) | ||
+ | |||
+ | Falls dies der Fall ist, funktioniert Ansprechen über ST-Link Adapter und gesetzten Junper P6 im " | ||
- | You will need : | + | Buttons, LEDs und LCD sind da noch nicht initialisiert. Erst wenn der Bootloader installiert wurde und läuft hat man minimalistisch die Peripherie-GPIOs initialisiert, |
- | - an up to date STM32 ST-LINK utility ( http://www.st.com/ | + | |
- | - a ST-LINKV2 probe ( http://www.st.com/ | + | |
- | - latest version of the Bootloader and/or UHSDR Firmware | + | |
- | The only tricky part is to connect the probe JTAP connector to the JP8 UI board, here are the needed wires : | + | Bei installiertem Bootloader: |
- | JP8-3 (SWDIO) to JTAG-7 | + | * Taste " |
- | JP8-4 (SWCLK) to JTAG-9 | + | * Taste "Band +" drücken, dann OVI40 UI board hochfahren ⇒ Boot Loader Update via kleine USB Buchse |
- | JP8-5 (UI_3V3) to JTAG-1 | + | |
- | JP8-6 (GND) to JTAG-20 | + | |
- | The rest of the procedure is straight forward | + | Prüfen: |
- | One additional trick, when I first connected to the MCU, I got an error message « Readout Protection Mode » and was unable to erase the chip. I finally choosed to try to flash a first time and the utility did what was necessary | + | * erkennt der PC das per USB angeschlossene OVI40 UI board (Gerätemanager / Device Manager)? |
+ | * PC USB port working? USB cable ok? | ||
+ | * Check all MCU pins are correctly soldered and no shortcuts exist: Use a thin knife / scalpell / tweezer, go inbetween | ||
- | [{{: | + | ==== NF Audio Verstärker geht nicht ==== |
- | A couple of us faced the same issue during beta testing the new UI board. | + | Bitte +12V Versorgung des NF Audio Verstärkers messen. Er wird vom OVI40 RF Board über P1 versorgt. |
- | But as you could see a cheap chinese ST Link adapter from Amazon or eBay saves your day | + | |
- | Here are the steps. Unfortunately in German but maybe it helps. | + | ==== USB Stick funktioniert nicht ==== |
- | https:// | + | |
- | Register values from Andreas: | + | |
- | https:// | + | |
- | The URLs are from a (forgotten) I40 UI thread in the mcHF folder. | + | Bitte +8V Versorgung von RF Board prüfen, JP1 (Pin29). |