logo
Welcome, Guest. Please Login or Register.
14. December 2024, 04:58:59


Home Help Search Login RegisterWIKIUHSDR Download

Amateurfunk Sulingen
Diskussions- und Newsboard des DARC-Ortsverbandes I40  |  allgemeine Kategorie  |  Selbstbauprojekte (Moderator: DF8OE)  |  Topic: New TRV using ready module <- zurück vorwärts ->
Pages: 1 ... 3 4 [5] Go Down Print
   Author  Topic: New TRV using ready module  (Read 63699 times)
DL2GMI - Michael (H44MI)
alter Hase
****

Offline

Posts: 371





View Profile WWW E-Mail
Re:New TRV using ready module
« Reply #60 on: 28. April 2021, 18:32:46 »

Hi Artur,

i just wan´t to give you a positive feedback:
My transverter is running fine and i had already my first QSO over QO-100.

Now, i have some questions:
1) Some Ham-Radio frieds of me are also interested in this TRV, but aren´t able to solder SMD and like this. Can we order ready installed Modules by you ?
2) Do you have further developed the transverter and which is the actual PCB-Revision ?
Because: when 1) is not possible, i think about to order some PCB and Cases and so on by you an give them to a company to soldering it.


Kind regards,

Michael
Logged

UI 4, RF 4, Mods: UI-H-031,RF-05-H-001,RF-H-002,UI-H-003,UI-H-004,RF-H-005,UI-H-006,UI-H-008,RF-H-018,RF-H-023,UI-H-027,RF-H-029,UI-N-026,RF-N-009,RF-N-010,RF-N-011,RF-N-012,AG-N-013,RF-N-015,RF-N-016,UI-N-019,UI-N-025,RF-N-028,RF-N-030
DL5LF
Neuling
*

Offline

Posts: 23



Ich liebe dieses Forum!

View Profile
Re:New TRV using ready module
« Reply #61 on: 04. May 2021, 18:52:39 »

Artur,

I still have a set v1.2. You recommend to use it or are there too many modifications?

Frank
Logged
dc2pd
Neuling
*

Offline

Posts: 4



Ich liebe dieses Forum!

View Profile
Re:New TRV using ready module
« Reply #62 on: 24. May 2021, 21:42:00 »

Hi Artur,

I'm thinking of building your transverter to add to my Eagle.
I have looked at the schematic and some questions :

- Your PTT is controlled by the incomming signal, which is passed thru an attenuator.
But in the first time - before the relais switched - the input signal from the transceiver is
feeded to the LC and the 50 R at the mixer. The relais is specified with 3ms switching time...
Have you measured the switching time of your circuit?

- You have added a DC bias to the POTY output. I think it is to activate your 20W amplifier.
Most users will not need it.

- There are no remarks on the used caps in the BOM. Most of the caps in the signal path have to be ATC types.

- Do you reach the drive level of the mixer? It is a level13 mixer.

73
Peter



Logged
DL2GMI - Michael (H44MI)
alter Hase
****

Offline

Posts: 371





View Profile WWW E-Mail
Re:New TRV using ready module
« Reply #63 on: 08. September 2021, 17:21:33 »

Do you think about a next version of the Transverter ? Maybe with a little bit more output (for example 3-4W) ?
With the Helix and the 2-2,5W the signal ist one of the weekest signals at the QO100-Transponder...
Logged

UI 4, RF 4, Mods: UI-H-031,RF-05-H-001,RF-H-002,UI-H-003,UI-H-004,RF-H-005,UI-H-006,UI-H-008,RF-H-018,RF-H-023,UI-H-027,RF-H-029,UI-N-026,RF-N-009,RF-N-010,RF-N-011,RF-N-012,AG-N-013,RF-N-015,RF-N-016,UI-N-019,UI-N-025,RF-N-028,RF-N-030
DL5LF
Neuling
*

Offline

Posts: 23



Ich liebe dieses Forum!

View Profile
Re:New TRV using ready module
« Reply #64 on: 23. October 2021, 14:18:16 »

I want to tune 2m from 144.5 to 145.0.

2255.5 MHz
595 MHz

Did anybody apply appropriate changes to the 2m section in the code?

...before I dig into the data sheet ....

I answer myself :-)
There is a SW for the Eval-Board... the register values are computed from output frequency.
Here are the values:

//PLL configuration
#define FREQ1 2255500      // kHz - F1 (used by default)
#define FREQ2 595000      // kHz - F2 (configure S1 = ON and S2 = OFF)
#define FREQ3 1960500      // kHz - F3 (configure S1 = OFF and S2 = ON)
#define FREQ4 300000      // kHz - F4 (configure S1 = ON and 22S2 = ON)

#define ADF4351_INT_F1 90
#define ADF4351_FRAC_F1 11
#define ADF4351_MODULUS_F1 50

#define ADF4351_INT_F2 95
#define ADF4351_FRAC_F2 1
#define ADF4351_MODULUS_F2 5


Tnx, Frank
« Last Edit: 23. October 2021, 16:45:43 by DL5LF » Logged
Pages: 1 ... 3 4 [5] Go Up Print 
Diskussions- und Newsboard des DARC-Ortsverbandes I40  |  allgemeine Kategorie  |  Selbstbauprojekte (Moderator: DF8OE)  |  Topic: New TRV using ready module <- zurück vorwärts ->
Jump to: 


Login with username, password and session length

 Es wird die Verwendung von Browsern die auf der "Blink"-Engine basieren und mindestens
1024x768 Pixel Bildschirmauflösung für die beste Darstellung empfohlen
 
Amateurfunk Die Beiträge sind, sofern nicht anders vermerkt, unter der folgenden Lizenz veröffentlicht:
GNU Free Documentation License 1.3 GNU Free Documentation License 1.3
verbindet!
Powered by MySQL Powered by PHP Diskussions- und Newsboard des DARC-Ortsverbandes I40 | Powered by YaBB SE
© 2001-2004, YaBB SE Dev Team. All Rights Reserved.
- modified by Andreas Richter (DF8OE)
Impressum & Disclaimer
Valid XHTML 1.0! Valid CSS!