Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:uhsdr:uhsdrbl [05.02.2018 17:04] – df9ts | en:uhsdr:uhsdrbl [06.02.2018 17:49] – df9ts_user | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | {{tag>stub}} | + | {{tag>review}} |
{{tag> | {{tag> | ||
- | ===== UHSDR Bootloader General Reading ===== | ||
- | |||
- | Forum: | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | |||
- | Github Wiki: | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | |||
==== Bootloader Installation - General Comments ==== | ==== Bootloader Installation - General Comments ==== | ||
Line 57: | Line 45: | ||
* {{ : | * {{ : | ||
* [[http:// | * [[http:// | ||
+ | * [[http:// | ||
==== Option 2: DeFuse Tool upgrade ==== | ==== Option 2: DeFuse Tool upgrade ==== | ||
Line 72: | Line 61: | ||
=== Further reading === | === Further reading === | ||
- | {{ : | + | * {{ : |
+ | * [[http:// | ||
Line 82: | Line 72: | ||
* Format USB-Stick with FAT file partition. MAke sure - just in case - that USB-stick is otherwise empty | * Format USB-Stick with FAT file partition. MAke sure - just in case - that USB-stick is otherwise empty | ||
* Copy .bin file to stick. Make sure it is copied as file, not just a link / short-cut | * Copy .bin file to stick. Make sure it is copied as file, not just a link / short-cut | ||
- | * OVI40 UI powered up with 5V and 8V (JP1). The 8V powers the USB stick via voltage regulator | + | * OVI40 UI powered up with 5V (Pin 28 JP1) and 8V (Pin 29 JP1) and GND (Pin 30 JP1). The 8V powers the USB stick via voltage regulator |
+ | * Recent UHSDR boot loader installed and working | ||
=== Procedure === | === Procedure === | ||
+ | - Supply +8V on JP1 pin 29 - to pwer USB stick | ||
+ | - Push and - important - hold switch "BAND -" | ||
+ | - Supply +5V on JP1 pin 28 - this starts the boot loader | ||
+ | - insert USB stick into large USB port of OVI40 UI | ||
+ | - Wait for FW upload to finish | ||
+ | - Release switch "Band -" | ||
+ | - Remove +5V, then apply again to reboot OVI40 UI. | ||
- | ==== Further reading | + | ==== Check proper working of newly loaded boot loader |
- | xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx | + | |
+ | Remove Jumper P6 if previously closed, then boot UI. | ||
+ | Check boot loader version number displayed in system menu corresponds to the version you intended to install. | ||
+ | ===== UHSDR Bootloader further reading ===== | ||
+ | Forum: | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | Github Wiki: | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
- | |||
- | |||
- | ==== Kontrolle der geladenen Bootloader Version ==== | ||
- | |||
- | Nach erfolgreicher Bootloader-Installation den " | ||
- | |||
- | Wenn Du im System-Menü der Firmware die Bootloader Version anzeigen lässt - was wird Dir dann angezeigt? Sollte es etwas anderes als 3.4.5 sein hol Dir bitte den Bootloader (.dfu - Datei) und flashe den mit Jumper und dem dfu-Tool. Und dann schau nochmal nach, ob dann der 3.4.5 angezeigt wird. | ||
- | |||
- | ==== Nachfolgende Bootloader Update Installationen ==== | ||
- | |||
- | < | ||
- | |||
- | |||
- | |||
- | |||
- | === Bootloader laden === | ||
- | |||
- | Siehe auch [[https:// | ||
- | |||
- | Stromversorgung dazu 5 Volt Pin 28+ , Pin 30 Gnd) | ||
- | |||
- | === UHSDR Firmware laden === | ||
- | |||
- | Nachdem im DFU mode (J6) der neueste Bootloader geladen wurde (bl-40SDR.dfu): | ||
- | |||
- | - +8V on JP1 pin 29 - zur Stromversorgung des USB stick! | ||
- | - Drücke und (wichtig!) halte Taste "BAND -" | ||
- | - +5V on JP1 pin 28 legen - um bootloader zu starten | ||
- | - USB stick in USB port stecken - auf richtigen Firmware Namen achten (fw-40SDR.bin) | ||
- | - Warten bis FW upload fertig ist | ||
- | - Taste "Band -" loslassen | ||
- | - +5V aus und wieder einschalten für OVI40 UI board reboot. | ||