Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
en:ovi40_uiboardtest [07.02.2018 16:12] – created df9ts | en:ovi40test:uiboardtest [08.02.2018 20:50] (current) – ↷ Page moved and renamed from en:ovi40_uiboardtest to en:ovi40test:uiboardtest df9ts | ||
---|---|---|---|
Line 35: | Line 35: | ||
In case you see this UHSDR error message please check +3V supply for codecs (WM8731) is ok. This +3V supply is generated on RF board. | In case you see this UHSDR error message please check +3V supply for codecs (WM8731) is ok. This +3V supply is generated on RF board. | ||
- | ==== MCU läuft gar nicht, auch DFU Verbindung geht nicht ==== | + | ==== MCU does not work, DFU connection / DfuSe not working also ==== |
- | Zuerst prüfen, ob die MCU in korrekter Lage eingelötet wurde ("Pin 1"). | + | First check that MCU is soldered in in correct orientation |
- | Nach dem booten legt die MCU 3.3V an die Taster. Um erfolgreich zu booten braucht die MCU: | + | In order to boot the MCU needs: |
- | * CPU Takt (-> TXCO Takt messen) | + | * CPU clock (-> |
- | * Korrekten Spannungsreset | + | * correct reset voltage over time at boot up (-> |
- | Falls dies der Fall ist, funktioniert Ansprechen über ST-Link | + | Only if thos pre-conditions are met will the MCU work with DfuSe or ST-Link/V2 and closed jumper |
- | Buttons, LEDs und LCD sind da noch nicht initialisiert. Erst wenn der Bootloader installiert wurde und läuft hat man minimalistisch | + | Only after bootloader starts correctly will pin voltages for switches, LEDs and LCD be initialized to some extend., e.g. " |
+ | " | ||
- | Bei installiertem Bootloader: | + | Also check: |
- | * Taste "Band -" drücken, dann OVI40 UI board hochfahren => große USB Buchse aktiviert für Firmwareupdate | + | * Does PC recognize the OVI40 UI board connected |
- | * Taste "Band +" drücken, dann OVI40 UI board hochfahren => Boot Loader Update via kleine | + | |
- | + | ||
- | Prüfen: | + | |
- | * erkennt der PC das per USB angeschlossene OVI40 UI board (Gerätemanager / Device Manager)? | + | |
* PC USB port working? USB cable ok? | * PC USB port working? USB cable ok? | ||
* Check all MCU pins are correctly soldered and no shortcuts exist: Use a thin knife / scalpell / tweezer, go inbetween MCU pins and try to push the pins gently sideways one by one, check if all are soldered to PCB. If not the pin moves slightly. | * Check all MCU pins are correctly soldered and no shortcuts exist: Use a thin knife / scalpell / tweezer, go inbetween MCU pins and try to push the pins gently sideways one by one, check if all are soldered to PCB. If not the pin moves slightly. | ||
- | ==== NF Audio Verstärker geht nicht ==== | + | ==== USB Stick does not work ==== |
- | Bitte +12V Versorgung des NF Audio Verstärkers messen. Er wird vom OVI40 RF Board über JP1 versorgt. | + | Please check +8V supply from Rf-Board, JP1. |
- | + | ||
- | ==== USB Stick funktioniert nicht ==== | + | |
- | Bitte +8V Versorgung von RF Board prüfen, JP1. | + | |