Les deux révisions précédentes Révision précédente | Prochaine révisionLes deux révisions suivantes |
fr:uhsdr:uhsdrbl [10.02.2018 21:49] – [Option 2: DeFuse Tool upgrade] df9ts_user | fr:uhsdr:uhsdrbl [10.02.2018 22:05] – [Option 3: USB-Stick upgrade upgrade] df9ts_user |
---|
* [[http://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stsw-stm32080.html|DfuSe Ressources and SW (bootom of page)]] | * [[http://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stsw-stm32080.html|DfuSe Ressources and SW (bootom of page)]] |
| |
==== Option 3: USB-Stick upgrade upgrade ==== | ==== Option 3: Mise à jour "boot loader" par clé USB ==== |
| |
ToDo | ToDo |
| |
=== Preconditions === | === Préconditions === |
| |
* Download latest bl-40SDR.bin bootloader from [[https://www.amateurfunk-sulingen.de/uhsdr/bootloader-latest/OVI40/|here]]. | * Téléchargez le plus récent bl-40SDR.bin "boot loader" d'[[https://www.amateurfunk-sulingen.de/uhsdr/bootloader-latest/OVI40/|ici]]. |
* Format USB-Stick with FAT file partition. MAke sure - just in case - that USB-stick is otherwise empty | * Formattez la clé USB avec FAT ou FAT32 |
* Copy .bin file to stick. Make sure it is copied as file, not just a link / short-cut | * Copiez fichier .bin sur clé USB. Vérifiez que le fichier a été copier et non pas seulement un raccourci |
* OVI40 UI powered up with 5V (Pin 28 JP1) and 8V (Pin 29 JP1) and GND (Pin 30 JP1). The 8V powers the USB stick via voltage regulator | * OVI40 UI alimenté avec +5V (Pin 28 JP1) et +8V (Pin 29 JP1) et terre (Pin 30 JP1). Les +8V sont l'alimentation pour la clé USB |
* Recent UHSDR boot loader installed and working | * "Boot loader" UHSDR récent installé et en état de marche |
| |
=== Procedure === | === Procédure === |
| |
- Supply +8V on JP1 pin 29 - to pwer USB stick | * Mettez +8V à JP1 pin 29 - pour alimenter la clé USB |
- Push and - important - hold switch "BAND -" | * Appuyez et restez appuyé sur la touche "BAND -" |
- Supply +5V on JP1 pin 28 - this starts the boot loader | * Alimenté +5V à JP1 pin 28 - cela pour démarrer le "boot loader" installé |
- insert USB stick into large USB port of OVI40 UI | * insérez la clé USB dans la prise USB large du OVI40 UI |
- Wait for FW upload to finish | * Attendez que le upload soit fini |
- Release switch "Band -" | * Relachez la touche "Band -" |
- Remove +5V, then apply again to reboot OVI40 UI. | * Enlevez, puis remettez +5V pour redémarrer le OVI40 UI |
| * Vérifiez le bon fonctionnement |
| |
==== Check proper working of newly loaded boot loader ==== | ==== Check proper working of newly loaded boot loader ==== |